Tianchi Stainless Steel Storage Tank YDS-30B-50 Stainless Steel
Storage Tank 30L Liquid Nitrogen Container
Storage-type liquid nitrogen containers (Tian Chi)
Stainless Steel Storage Tank 30L are mainly designed for special
earthquake protection. In addition to standing storage, they can
also be transported under liquid nitrogen conditions, but severe
collisions and vibrations should be avoided.
The produced by Tianchi is made of high-strength aluminum alloy,
high-vacuum multi-layer super insulation structure, light weight,
liquid nitrogen static daily steam loss is small.
Main Structure and feature
The Container is mainly composed of outer shell, inner vessel,
neck, multi-layer heat insulation and canister etc.
1 The outer shell and inner vessel are made of the aluminum alloy
plate featuring light weight, high cryogenic strength and corrosion
2 The neck tube is made of glass fiber reinforced plastics
featuring high mechanical strength and low heat conductivity.
3 The multi-layer insulation is composed of the reflecting screen
of aluminum foils with high reflectivity and insulation material
with low conductivity and low gas-passing speed to reduce heat
4 The jacket between the outer shell and inner vessel is high
vacuum to prevent thermal convection. Moreover, an adsorbent with a
high adsorbing capacity at the cryogenic temperature is used to
ensure the long-term stable and reliable performance of container.
Company: Henan Tianchi Instrument & Equipment Co., Ltd.
Tel: +86-18903712477 +86-371-56788280
Address:Jinshui District, Zhengzhou City, Zheng Hua Road No. 10
Product Technical Parameters Table
|Static Power Dissipantion(Kg/D)|
1.High strength aluminium alloy structure;
2.Advanced powder coating technique;
3.Multi-layer thermal isolation design;
4.Protective jacket to prevent collision;
5.5-year warranty on vacuum;
Instruction for the Container Model
A. Diameter (mm) ,size is not marked it is 50mm.
B. The capital Latin Letter means special type(B-for
C. Nominal volume of container
e.g.1:YDS-35-50 means volume 35L,Dia.50mm,liquid nitrogen
e.g.2:YDS-50B-80 means volume 50L,Dia.80mm,liquid nitrogen
This series of liquid nitrogen container products have the
1.High-strength aluminum alloy structure, light emptied weight
2.The lock device can be installed to the container lid upon users
3.More than 5 years of vacuum quality promise is ensured with the
multi-layer thermal isolation design
4.The products are accessory with protective cover, which enhances
the protection from reel and stumble
1. Before use, please open the cover, with liquid nitrogen, liquid
nitrogen filling after tightening cover, closed safety valve.
2 .If you need to spray pipe, then only open the valve, and close
the valve at the same time, and then open the power supply can be.
If you need a pipe spray, then open the next valve, while closing
the valve, and then open the power supply can be (Recommended).
If you need to up and down the pipeline at the same time spray,
then open up and down the valve can be, and then open the power
switch can be.
Note: please open the valve, and then connect the power supply.
3 . The use of the process, the valve can be adjusted according to
the amount of spray.
Note: If the spray mouth cream please promptly with a hot air dryer
to remove, so as not to affect the quality of spray.
4. Use is completed, if the liquid nitrogen in the tank is not
used, please turn off the power supply, then exhaust.
Note: Please disconnect the power supply, then open the vent valve,
prohibit direct exhaust.
Cleaning steps are as follows:
A.After the liquid nitrogen volatile, the rest for a few hours, the
container temperature to return to room temperature.
B. The water 40℃-50℃ into the container, and then wipe with a
C. Rinse with water 2-3 times.
D.The container upside down to dry naturally, can also be dried
with hot air, suitable temperature is 40℃-50℃, avoid higher than